Built 2026-11-20 (20 November 2026)

How Fairway Depth Limits What a Barge Can Carry

A ship floats because it displaces water, and the more it carries, the deeper it sits. The depth of the hull below the waterline is its draft. A loaded vessel needs water at least as deep as its draft, plus room under the keel. When rivers fall, the water above the shallowest stretch of the route shrinks, and the draft that stretch allows shrinks with it. The cargo has to shrink to match. That is the whole mechanism behind low water and freight.

Draft and the load it allows

Every vessel has an empty draft, the depth it sits at with no cargo, and a full draft, the depth at its design load. Between the two, draft rises roughly in step with cargo weight. For a river barge or motor vessel, the difference between empty and full draft is a couple of metres, and that is where all the cargo capacity lives. If the available depth is above the full draft plus a margin, the vessel can load fully. If it is between the empty and full draft, it loads part of its capacity. If it is at or below the empty draft plus the margin, the vessel can carry almost nothing.

This is why small changes in river depth can cause large changes in load. A drop of half a metre can take a large share of a vessel’s capacity away, because half a metre is a large share of the couple of metres that separate empty from full.

Where the depth comes from

On the Rhine, the authority publishes a guaranteed fairway depth as a rule based on the gauge reading: the reading minus the equivalent low water level plus the nominal depth. The explainer on GlW describes the values. The result is the official nominal fairway depth for the stretch of river around the gauge. It is guaranteed by the authority, so it is a fair starting point for anyone reasoning about loads.

The safety margin

A skipper will not sail with the keel almost on the bed. The margin between the guaranteed depth and the loaded draft leaves room for inaccuracy in the depth, for the vessel sinking slightly as it moves, and for waves. How large the margin is depends on the vessel, the stretch of river and the skipper. This site uses a default of 0.30 metres, taken from a non-official source, and marks it as unverified. The load factor calculator lets you change it to see how sensitive the answer is.

The estimate step by step

The estimate the site shows follows four steps, and each one is visible on a gauge page and in the calculator:

  1. Take the official nominal fairway depth for the current reading.
  2. Subtract the safety margin to get the allowed draft.
  3. Hold the allowed draft between the vessel’s empty and full draft.
  4. Read the load share as the position between empty and full: zero at the empty draft, one at the full draft.

The result is labelled an estimate wherever it appears. It is not a statement about any real vessel, and it is not a forecast of what a barge operator will do. It is a way to turn a river level into a number that says how much shipping capacity a stretch of river can support, using published values that a reader can check.

What the estimate leaves out

The estimate uses a linear rule between empty and full draft. Real vessels are not perfectly linear, cargo types differ in density, and some vessels are built to sail shallower than others. The reference vessels used here are typical planning values, not data from a specific ship, and the site says so next to each one. The estimate also ignores the depth of shallower spots elsewhere on a route, tow configurations, and restrictions from lock schedules or bridges. On the Mississippi the site shows no load estimate at all, because no verified rule links river stage to loadable draft there.

Using the number

If you are reading the estimate to understand a market, treat it as a rough gauge of pressure: a load share near 100 percent means little constraint, a share near zero means very little cargo can move, and the range in between is where prices and surcharges tend to change. If you are making an operating decision, use the authority’s own notices and your operator’s advice. This site is informational and not for navigation.

Frequently Asked Questions

Is the load percentage on this site an official figure?

No. It is an estimate calculated by this site from the official fairway depth, a safety margin and reference values for a typical vessel. It is always labelled as an estimate, and the reference vessel values and margin are not yet confirmed by a primary source.

Why can a barge carry almost nothing when the river is not dry?

A barge floats lower as it loads. Its empty draft is already about a metre, so when the fairway depth less a margin falls to around that, there is almost no room to add cargo without touching the bed.

Source: WSV and GDWS via PEGELONLINE (pegelonline.wsv.de), DL-DE->Zero-2.0. Raw, unvalidated data. Data as of 2026-09-21 (explainer last reviewed). Figures quoted in this explainer come from the pages linked above.